Products:
Allegro II Cement Coating provides a cost-effective, durable and long-lasting colored coating that can be applied to portland cement surfaces such as: Stucco, Paint grade stucco, Concrete block/Concrete masonry unit (CMU) and Precast concrete.
An adhesive to laminate EPS to listed substrates. A 100% acrylic polymer base. Ready to use, applied without the addition of cement. Exceptional workability.
LaHabra Exterior Stucco Color Coat provides a lasting, durable color finish over LaHabra Fiber-47 Fastwall Scratch & Brown, LaHabra Fastwall Stucco Base, portland cement plaster "brown coat" and Parex USA Stucco Level Coat. It is integrally colored with fade-resistant pigments, and is economical with low maintenance. Product is available in premix or tint Base.
LaHabra Exterior Stucco Color Coat is available in the following bases/aggregate size for use with LaHabra Color Packs:
* Base 100 16/20 * Base 200 16/20
* Base 100 20/30 * Base 200 20/30
Excellent as a base for smooth finishes. No moist curing required. High PSI. High tensile strength. Under normal conditions, ready to accept finish after 24 hours. Fastwall Accel-Cure is a factory controlled high-quality blend of portland cement, lime, fibers and proprietary additives that conforms to ASTM C926. ASTM C897 or ASTM C144 sand is added at the job site. Can be installed up to 1/2 in. (12.7mm) in one application.
A factory controlled high-quality blend of portland cement, lime, fibers and proprietary additives that conforms to ASTM C926. ASTM C897 or ASTM C144 sand is added at the job site. Can be installed up to 1/2 in. (12.7mm) in one application.
A factory controlled high-quality blend of portland cement, lime, fibers, proprietary additives and ASTM C144 sand that conforms to ASTM C926. Factory-blended mix that requires only the addition of water. Can be installed up to 1/2 in. (12.7mm) in one application.
A factory controlled high-quality blend of portland cement, lime, fibers and proprietary additives that conforms to ASTM C926 is designed as a replacement to job-site mixed scratch and brown base coats. ASTM C897 or ASTM C144 sand is added at job site.
A factory controlled high-quality blend of portland cement, lime, fibers, proprietary additives and ASTM C144 sand that conforms to ASTM C926 is designed as a replacement to job-site mixed scratch and brown base coats.
Fog Coat provides cost-effective, durable and long-lasting colored coating for existing stucco. It is easy to apply and specifically designed to refresh the color of stucco. A decorative coating for portland cement based stucco walls and ceilings.
A base Coat for LaHabra EIFS. Adhesive to laminate EPS to listed substrates. Applied without the addition of cement. Mixed on site with water. Excellent workability.
A base coat for LaHabra EIFS. Adhesive to laminate EPS to listed substrates. Used in a 50% acrylic paste to 50% portland cement by weight ratio. Requires the addition of portland cement.
NTS Exterior Color Coat is the next leap in stucco technology. NTS provides a lasting, durable color finish that can be applied over LaHabra FastWall Fiber-47 Scratch and Brown, LaHabra Fastwall Stucco Base, portland cement plaster "brown coat" and Parex USA Stucco Level Coat by hand or machine application.
LaHabra NTS Exterior Stucco Color Coat is available in the following bases/aggregate size for use with LaHabra Color Packs:
* Base 100 16/20 * Base 200 16/20
* Base 100 20/30 * Base 200 20/30
4.5 oz fiberglass mesh 19 in (48.2 cm) wide mesh. Self-adhesive, facilitates the wrapping of complex contours. Is alkali-resistant. NOTE: Complex architectural details only, not for use on full walls.
4.5 oz fiberglass 38 in. (96.5 cm) wide mesh. Is highly flexible for full walls or details. Is alkali-resistant. Standard reinforcement of Parex USA EIFS walls for impact resistance and details. Required in combination with 358.14 High Impact Mesh or 358.20 Ultra High Impact Mesh. May be used in Parex USA Krak-Shield assemblies.
4.5 oz fiberglass 9.5 in. (24 cm) wide mesh. Is highly flexible for use on details. is alkali-resistant. Ideal for use in back wrapping, corners, reveals and trim. May be used in combination with 355, 358.6 & 358.10 meshes in Parex USA Krak-Shield assemblies.
7.2 oz fiberglass 9.5 in. (24 cm) wide mesh. Is a heavy duty mesh designed to fold uniformly around corners to reinforce, enhance impact and abuse resistance.. Is alkali-resistant. Used in combination with 355 Standard Mesh, 356 Short Detail Mesh, 358.10 Intermediate Mesh, 358.14 High Impact Mesh or 358.20 Ultra High Impact Mesh. May be used in Parex USA Krak-Shield assembly.
12 oz fiberglass 38 in. (96.5 cm) wide mesh. Is an intermediate strength mesh used to enhance impact and abuse resistance. Is alkali-resistant. Use with Parex USA EIFS to achieve EIMA's medium impact strength classification. Can be used in combination with 355 Standard Mesh and 356 Short Detail Mesh. May be used in Parex USA Krak-Shield assembly.
15 oz fiberglass 38 in. (96.5 cm) wide mesh. A high strength mesh used to enhance impact and abuse resistance. Is alkali resistant. Use with Parex USA EIFS to achieve EIMA's high-impact strength classification. 355 Standard Mesh is required in combination with 358.14 High Impact Mesh.
20 oz fiberglass 38 in. (96.5 cm) wide mesh. Is an ultra high strength mesh used to enhance impact and abuse resistance. Is alkali-resistant. Use with Parex USA EIFS to achieve EIMAs ultra-high impact strength classification. 355 Standard Mesh is required in combination with 358.20 Ultra High Impact Mesh.
Parex USA 365 Flashing Membrane is a self-sealing rubberized asphalt membrane that functions as a moisture and air barrier. It is 30 mils (0.75 mm) thick and black in color. It can be applied to various substrates such as wood, metal, gypsum sheathing and to house wrap and other weather resistive barriers. The Parex USA 365 Flashing Membrane is unique: it is faced with a non-woven, integrally bonded fabric that enables adhesion of Parex adhesives. It functions as a seal and flashing at sills of rough openings, deck framing, etc., interfacing with the building substrate and other weather resistive barriers.
Our Flashing Membrane is offered in 3 sizes:
* 3" x 100'
* 6" x 100'
* 12" x 100'
Speeds and simplifies application of the WaterMaster systems and assemblies. Eliminates need for pre-wrapping or rasping the back of boards at terminations. Eliminates the need for mineral wool and track at terminations.
Non-woven fabric used to tape the joints of the sheathing boards to which a Parex liquid water-resistive barrier is applied.
Our Sheathing Tape is offered in 3 sizes:
* 4" x 500'
* 6" x 500'
* 9" x 500'
A 100% acrylic transparent coating. Contains EPA-registered mildewcide and algicide. Dirt resistant. The coating hardens and does not soften under solar heating. The nontacky surface provides high resistance to accumulation of dirt and pollutants. Water vapor permeable.
A 100% acrylic transparent coating. Developed with a special matte agent to reduce sheen.Contains EPA-registered mildewcide and algicide. Dirt resistant. The coating hardens and does not soften under solar heating. The nontacky surface provides high resistance to accumulation of dirt and pollutants. Water vapor permeable.
Rapid set admix for any Parex USA polymer modified EIFS Base Coat & Adhesive to reduce set time for Winter weather or quick EIFS patch & repair work.
100% acrylic emulsion designed for use with for portland cement based products. High-performance acrylic polymer bonding agent. Admixture in portland cement based mixes.
A 100% acrylic-based non-textured coating. DPR (Dirt Pick-up Resistance): The non-tacky surface provides high resistance to accumulation of dirt, mold, and pollutants. Excellent hiding power as well as flexibility and drying characteristics. The surface of the coating hardens and does not soften under heat. Integrally colored with high quality pigments.
NEW PRODUCT - A 100% dry acrylic-based textured finish. Mix on-site with water water and pigment. VOC free and freeze thaw stable Dry-Tex is made Dirt Pick-Up Resistance (DPR) meaning the surface of the finish hardens and does not soften again under heat. The non-tacky surface provides high resistance to accumulation of dirt, mold, and pollutants.
Dry-Tex is offered in two textures:
* Sand Coarse
* Sand Fine
View the Dry-Tex Mixing and Application Video
A 100% acrylic Elastomeric non-textured coating. Highly flexible: can bridge existing hairline cracks. DPR (Dirt Pick-up Resistance): The non-tacky surface provides high resistance to accumulation of dirt, mold, and pollutants. It provides excellent hiding power as well as flexibility and drying characteristics. The surface of the coating hardens and does not soften under heat. Integrally colored with high quality pigments.
Is a 100 percent acrylic-based primer that improves the mechanical bond of the finish to the stucco substrate. PrimeShield reduces the chance of efflorescence which may result from the cement content of various bases. It also enhances the appearance and uniformity of the finish. The product is water-vapor permeable and does not create a vapor retarder.
Granular sulfamic acid crystals, mixed with water to produce a surface cleaner for tile, grout, stucco, EIFS, concrete and masonry surfaces.
Pro-Tect is a clear water repellant used to protect stucco, masonry and mature concrete from water, enhancing the beauty of cementitious stucco, masonry and mature concrete by improving stain resistance. Pro-Tect maintains the beauty of stucco by reducing susceptibility to freeze-thaw damage, efflorescence, biological growth. Available in both one and five gallons.
A base coat and adhesive for Parex USA EIFS. Single component 100% acrylic polymer base. Ready to use, applied without the addition of cement. First EIFS base coat & adhesive to be packaged in a box for easier waste management on the jobsite and less impact on landfills.
Water-based acrylic curing membrane formulated to provide excellent performance in the water retention section of ASTM C 309. Provides a curing membrane over cementitious surfaces allowing acrylic finishes to be applied quickly, while protecting against delamination and efflorescence. Provides a sound, sealed substrate for a uniform finish over either stucco or concrete.
A 100% Acrylic sandable basecoat that comes as a white base. It enhances the appearance and uniformity of smooth finishes. It can be easily recoated with Parex USA Allegro II. Ideal over EIFS basecoats, stucco basecoats, stucco finishes, and interior drywall.
Stucco Level Coat is a surface leveler and mesh adhesive for use in Parex USA Krak-Shield assemblies. Bonds to stucco brown coat. Can be applied in a thin layer. Applied without the addition of cement. Mixed on site with water only. Excellent workability.
4.5 oz fiberglass 38 in. (96.5 cm) mesh. For increased crack reduction and strength. Embed in Stucco Level Coat to smooth and level surface for finish. Use with Krak-Shield and Krak-Master stucco assemblies. Not for use on EIFS.
A 100% acrylic-based elastomeric textured finish. Made with DPR (Dirt Pick-up Resistance) chemistry. Is highly flexible: can bridge pre-existing or existing hairline cracks. Integrally colored with high quality pigments.
LaHabra Perma-Elastic Elastomeric Finish is available in three textures.
* Fine |
* Coarse |
* Swirl |
A 100% acrylic-based textured finish. Made with Dirt Pick-Up Resistance (DPR) meaning the surface of the finish hardens and does not soften again under heat. The non-tacky surface provides high resistance to accumulation of dirt, mold, and pollutants. The finish is integrally colored with high quality pigments.
LaHabra Perma-Finish EIFS & Stucco Acrylic Finish is available in four textures.
* Fine | * Smooth |
* Swirl | * Coarse |
A 100% acrylic-based textured finish for stucco only. Made with Dirt Pick-Up Resistance (DPR) meaning the surface of the finish hardens and does not soften again under heat. The non-tacky surface provides high resistance to accumulation of dirt, mold, and pollutants. The finish is integrally colored with high quality pigments.
LaHabra Perma-Flex Stucco Grade Acrylic Finish is available in four textures.
* Fine | * Smooth |
* Swirl | * Coarse |
A 100% acrylic-based primer. Reduces the chance of efflorescence which may result from the cement content of various bases. Enhances the appearance and uniformity of the finish. Water-vapor permeable. Does not create a vapor retarder. Improves acrylic and elastomeric finish coverage.
Plaster mix is a decorative lime-based plaster and stucco finish for interior and exterior use. It offers a number of finishes such as ultra smooth, sand finish, texture and spray applied. It is formulated with both lime and portland cement for strength and durability. It can be mixed with water and Admix100 for superior adhesion and strength. It can be tinted and/or stained, painted or left as is for a natural white finish.
Poly-Bond is for use as a basecoat and adhesive for expanded polystrene foam shapes. These shapes are typically used as exterior decorative trim such as pop-outs, plant-ons, cornices and quoins.
LaHabra Poly-Bond is offered in 2 textures:
* Coarse: for maximum keying strength
* Fine: for complex architectural details
LaHabra Santa Barbara Mission Finish provides a lasting, durable smooth stucco finish over LaHabra Fiber-47 Fastwall Scratch & Brown, LaHabra Fastwall Stucco Base, exterior plaster "brown coat" and Parex USA Stucco Level Coat. It is integrally colored with fade-resistant pigments, and is economical with low maintenance. Product is available in premix or tint Base.
LaHabra Santa Barbara Mission Finish is available in 2 bases for use with LaHabra Color Packs:
* Base 100 * Base 200
Admix100 is a ready mix, premium quality, acrylic polymer specifically designed for modifying portland cement mortars, plasters, stuccos, and concrete mixes. It is a water-based acrylic polymer and dries to a uniform color with no tendency toward yellowing or discoloration. It improves adhesion, cohesion, compressive, tensile, and flexural strengths of cement-based materials.
Aged Limestone is a polymer modified finish designed for interior and exterior applications. It is a blend of select aggregates and other minerals that produce a hard durable finish available in Fine and Coarse. This versatile easy to use product offers an infinite number of patterns and textures ranging from smooth to coarse unfinished stone. You can spray the material or use stencils, brushes or rollers to create the texture you want, giving you endless possibilities to satisfy the most demanding taste.
Antiquing Gel is a water-based, tinted, semitransparent, acrylic emulsion for providing an old world, antique effect. It is both decorative and protective. Antiquing Gel is permeable to water vapor and resistant to blistering.
Cerastone is an attractive multi-color wall finish made of colored aggregates. Made with a clear 100% acrylic vapor-permeable binder. Can be used in interior and exterior application. Ideal for high traffic interior areas. Highly durable, scratch-resistant finish. Can be easily repaired. Requires the use of Parex USA 610 Matte Clear Sealer.
100% acrylic based metallic coating. Economically replicate the look of metal panels with the ease of a coating application. Includes dirt pick-up resistance (DPR) which ensures the coating does not soften under head and resists accumulation of dirt, mold, and pollutants.
A 100% acrylic-based sanded primer. Reduces the chance of efflorescence which may result from the cement content of various bases. Enhances the appearance and uniformity of the finish. Water-vapor permeable. Does not create a vapor retarder. Improves finish coverage.
SprayStone is an attractive multi-color wall finish made of colored aggregates. Made with a clear 100% acrylic vapor-permeable binder. Can be used in interior and exterior application. Ideal for high traffic interior areas. Highly durable, scratch-resistant finish. Can be easily repaired. Requires the use of Parex USA 610 Matte Clear Sealer.
Stucco d'Raffinato is a durable 100% acrylic finish that can be used to create an almost endless variety of textured looks for interior and exterior walls and ceilings ranging from semi-smooth to heavy raised relief or made to resemble surfaces that include rustic stone or the appearance of an Old World Plaster finish.
An attractive multi-color wall finish made of colored aggregates. Made with a clear 100% acrylic vapor-permeable binder. Can be used in interior and exterior application. Ideal for high traffic interior areas. Highly durable, scratch-resistant finish. Can be easily repaired.
Tuscan Stucco is a decorative, multi-effect, versatile macrylic finish. It is a tintable, sandable finish for use on interior and exterior surfaces to obtain finish levels ranging from textured to smooth, resembling the appearance of an Old World Plaster finish.
Venetian Plaster is an interior acrylic plaster made with the highest quality ingredients. It is a unique decorative and protective coating designed for faux finishing, creating a polished, flat, pearlescent, metallic, or iridescent patina quickly and easily on walls, columns, and ceilings. Venetian Plaster provides dramatic high quality finish results and nearly endless design applications. It can simulate the visual effect of marble, granite and semiprecious stones with near infinite color variations.
Venetian Plaster Matte is an interior and exterior acrylic plaster made with the highest quality ingredients. It is a unique decorative and protective coating designed for matte/flat faux finishing. It is easy and quickly applied to walls, columns, and ceilings. Venetian Plaster Matte provides dramatic high quality finish results and nearly endless design applications. It can simulate the visual effect of old world marble and old world plaster with near infinite color variations.
Venetian Plaster Matte Base is an interior and exterior acrylic plaster made with the highest quality ingredients. It is an unique decorative and protective coating designed for matte faux finishing. It is easily and quickly applied to walls, columns and ceilings. Venetian Plaster Matte Base is generally used as a basecoat for Venetian Plaster Matte Finish.
Venetian Plaster Topcoat, available in clear or metallic, adds beauty and distinctive features to Venetian Plaster. It is a water-based, 100% acrylic protective coating that provides moisture resistance and increases the durability of Venetian Plaster.
A 100% Acrylic co-polymer fast d